Guida all'integrazione per Webex per Cisco BroadWorks

Data	Versione documento	Descrizione della modifica
12 maggio 2023	1.7	Aggiunti miglioramenti alla ricerca nella rubrica per i dispositivi Cisco RoomOS integrati Webex per BroadWorks e per i dispositivi RoomOS integrati W4B nella sezione Funzioni utente finale per dispositivi integrati Webex.
27 febbraio 2023	1.6	Aggiornata la procedura Configura servizi per Room OS in Onboarding dispositivi.
17 febbraio 2023	1.5	Aggiunta della sezione Cronologia chiamate unificata per i telefoni MPP Webex aware in Funzioni utente finale per dispositivi integrati Webex.
14 ottobre 2022	1.4	Processo di onboarding aggiornato per Room OS nella sezione Onboarding OS Room per includere i record SRV. Aggiornati i requisiti di configurazione BroadWorks nella sezione Prerequisiti Room OS con il puntatore alla Guida alla soluzione per i requisiti di provisioning flowthrough.
20 giugno 2022	1.3	Aggiornati i prerequisiti Room OS e i prerequisiti del dispositivo MPP con il puntatore alla Guida alla soluzione per i requisiti di provisioning flowthrough. Aggiornata la fornitura dei dispositivi Room OS e la fornitura del dispositivo MPP per includere informazioni sui diversi metodi di provisioning.
3 giugno 2022	1.2	Numero di attivazione della funzione di tipo di profilo dispositivo corretto (02283) in Prerequisiti Room OS e Prerequisiti dispositivo MPP
27 maggio 2022	1.1	Requisito corretto per l'istanza DMS dedicata per organizzazione partner. Aggiunto capitolo Prefazione . Titolo aggiornato come "Guida all'integrazione del dispositivo".
20 maggio 2022	1.0	Pubblicazione iniziale

Device Onboarding Overview

This chapter describes how to onboard devices to Webex for Cisco BroadWorks. This chapter covers the following use cases:

Onboard new Webex Room OS devices (using activation codes)
Onboard new MPP devices
Add Webex capability to existing MPP devices

We recommended that you deploy this feature on Release Independent ADP servers. However, XSP also supports this feature. If you're using XSP, then where this document refers to "ADP", you can substitute "XSP", unless the text specifies ADP only.
This feature supports both Personal and Workspace devices.

Room OS Onboarding

Webex for Cisco BroadWorks supports activation code onboarding for both shared and workspace Room OS devices.

Device Onboarding with Activation Codes

Device Onboarding with activation codes provides a simple and secure way to onboard Room OS devices. An activation code is a 16-digit one-time system-generated passcode that a user must input on a device to onboard the device. The activation code is securely linked to the intended user account and assures that only the intended user onboards a device linked to the same account. After the user enters the correct code, the device connects to both Webex and BroadWorks, completes registration, downloads its configuration file, and is ready to use.

The following Room OS devices support onboarding with activation codes:

Webex Board Series (Room OS)
Webex Desk Series (Room OS)
Webex Room Series (Room OS)

Onboarding Process for Room OS

The following process shows what happens when a Room OS device onboards using activation codes:

The partner administrator provisions the primary user and device in BroadWorks and then generates the activation code in BroadWorks.
An email that contains the device activation code is sent to the device owner.
The device owner starts the device.
The device prompts the device owner to enter the activation code.
The device owner enters the activation code on the device.
The device onboards to BroadWorks and Webex using the following subprocess:
- The Room OS device sends an activation request to Webex services. The activation code gets validated by GDS and if the code is correct, the device onboards to Webex. Webex returns a machine token to the device.
- The device sends an activation request to the BroadWorks DM along with the machine token and MAC address.
- BroadWorks authorizes and onboards the device.
- The device sends a request to the BroadWorks DM for an updated config. The machine token is included for authorization.
- BroadWorks authorizes the token, locates the updated config file, and returns an updated configuration file.
- Room OS will attempt to locate a NAPTR record for the domain specified in the configuration file as it expects to find an SRV entry for _sip._tls.<domain_in_config> if no NAPTR record is present then RoomOS will then try and look for an SRV record followed by an A record respectively.
  
  The SRV record must be _sip._tls. as roomOS will only support TLS for transport and SRTP for media.
The device registers and is ready to use.

The following diagram provides a simplified overview of the onboarding process.

For detailed information on Room OS onboarding, including more detailed flow diagrams, see the feature description Cisco BroadWorks Enhancements for Webex-Aware Device Onboarding.

Device Authentication (via OAuth Bearer Tokens)

Device authentication for Room OS devices requires that you enable Cisco OAuth Bearer Tokens on BroadWorks. During onboarding, the bearer token gets passed via the Activate Authorization header and serves to identify the device. The IdP validates the bearer token and returns the UUID (a machine UUID for workspace devices or user UUID for personal devices) as bearer subject. BroadWorks saves the UUID as the device name in the Network Server.

Room OS Prerequisites

Minimum Room OS Version

Room OS 10.13 minimum

BroadWorks Patch Requirements

This feature is supported as of version 2021.11 of the Release Independent (RI) ADP server with no patch requirements.

For non-RI servers, you must have installed the following patches (from patch groups ap381367, ap381951, ap382198) in order to use the feature. Install the patches that apply to your release:

Per R22:

AP.as.22.0.1123.ap381367
AP.as.22.0.1123.ap382236
AP.nfm.22.0.1123.ap381367
AP.ns.22.0.1123.ap381367
AP.platform.22.0.1123.ap381367
AP.platform.22.0.1123.ap382198
AP.ps.22.0.1123.ap381367
AP.xsp.22.0.1123.ap381367
AP.xsp.22.0.1123.ap382198

Per R23:

AP.as.23.0.1075.ap381367
AP.as.23.0.1075.ap382236
AP.ns.23.0.1075.ap381367
AP.platform.23.0.1075.ap382198
AP.platform.23.0.1075.ap381367
AP.xsp.23.0.1075.ap381367
AP.xsp.23.0.1075.ap382198
AP.ps.23.0.1075.ap381367

Per R24:

AP.as.24.0.944.ap381367
AP.as.24.0.944.ap381951
AP.as.24.0.944.ap382236

BroadWorks Platform Requirements

This feature is available on:

R22: available on XSP only
R23: available on XSP or ADP (Release Independent)
R24: available on ADP (Release Independent)

BroadWorks Configuration Requirements

To implement this solution, the Flowthrough provisioning must be configured to allow Broadworks to provision devices to Webex.

While configuring the Flowthrough provisioning, it’s not mandatory to use flowthrough provisioning to provision users i.e., you can continue to use your existing provisioning methods (API, Trusted/Untrusted Email, User self, etc.) to provision users. See "Provisioning Requirements" in the Webex for Cisco BroadWorks Solution Guide.
Make sure that the Integrated IM+P service is enabled on BroadWorks and points to the BroadWorks Provisioning Bridge.

The Provisioning Bridge URL was assigned when the Customer Template was applied to the organization. This should have been completed during your initial Webex for Cisco BroadWorks setup. To find the existing URL in Partner Hub, see Configure Application Server with Provisioning Service URL in the Webex for Cisco BroadWorks Solution Guide.
If you have multiple partner organizations, you require a dedicated Device Management Service (DMS) instance per partner.

Prerequisites for Activation Code Onboarding with Room OS

Make sure that the following is set:

Deploy the Device Activation Service on BroadWorks. For details, see Cisco BroadWorks Secure Onboarding Using Activation Codes.
Verify that the DAS URL setting for the BroadWorks cluster is set to the Device Management Services (DMS) URL. To view the current DAS URL setting in Partner Hub, go to Settings > BroadWorks Calling > View Clusters and select the appropriate cluster. The URL appears under Interface settings.

The following BroadWorks features must be activated on the AS:

101377 Enhancements for Webex and MPP device onboarding
25088 Support Handsets for DECT Devices
24104 Support Multicell Chaining for DECT devices
20077 Device Management Enhancements
19559 Visual Device Management Enhancements
02283 Device Profile Type Customization Enhancements

For example, run the following command to enable 101377. Change the feature number when activating the other features: AS_CLI/System/ActivatableFeature> activate 101377

If all the listed patches are installed and an activatable feature is not listed for your particular AS release, it is because it is already included in your AS base release and does not require activation.

Run the following CLI command on the Network Server:

NS_CLI/System/DeviceManagement> asLocationLookupEnabled true

Make sure that the CA that signs your SBC certificate is listed in the Room OS Trust List. You can view the Room OS trust list from the Device Web Portal. On the portal, select Security > Collaboration Edge to view the list of CAs.

Room OS Onboarding Flow

Complete the following tasks to configure your system to support Device Onboarding with Activation Codes for the following Webex Room OS devices:

Webex Board serie
Serie Webex Desk
Webex Room serie

1	Configure Services for Room OS Configure BroadWorks support for Room OS devices.
2	Provision Room OS Devices Provision the new device on BroadWorks.
3	Request Activation Code In the Device Profile, request an activation code. The code will be emailed to the primary user automatically.

Configure Services for Room OS

Before you can onboard any new Room OS devices, set the following system level parameters to turn on OAuth authentication.

Raise a Service Request with your onboarding agent or with Cisco TAC to provision Cisco OAuth for your Cisco Identity Provider Federation account. Title your service request "ADP AuthService Configuration".

If you already obtained Cisco OAuth Identity Provider credentials using one of the flows in this document, there’s no need to create a new request. However, if you obtained Cisco OAuth credentials using a flow that is not in this document, complete a new service request to update your credentials.

Cisco fornisce un ID client OAuth, un segreto client e un token di aggiornamento validi per 60 giorni. If the token expires before you use it with your ADP, you can raise another request.

Enable OAuth by using this CLI command:

ADP_CLI/Applications/BroadworksDms/AccessControl/Authentication/OAuth> set enable true

Make sure that the OAuth scope includes broadworks-connector-user (the scope is enabled by default). Run this command to check your scopes:

ADP_CLI/Applications/BroadworksDms/AccessControl/Authentication/OAuth/Scopes> get

Configure the Cisco Identity Provider parameters using the below CLI commands.

ADP_CLI/System/CommunicationUtility/DefaultSettings/ExternalAuthentication/CiscoIdentityProvider> set enabled false

set clientId <clientId>—see service request response for ID.
set clientSecret <clientSecret>—see service request response for secret.
set issuerName <URL>—see following table for URL.
set issuerUrl <URL>—see following table for URL.
set tokenInfoUrl <IdPProxy_URL>—see following tables for URL.
impostazione di ciResponseBodyMaxSizeInBytes 65536

Tabella 1. Set issuerName and issuerURL
Se Cluster CI è...	Set issuerName and issuerURL to...
USA-A	https://idbroker.webex.com/idb
UE	https://idbroker-eu.webex.com/idb
USA-B	https://idbroker-b-us.webex.com/idb
If you don't know your CI Cluster, you can obtain the information from the Customer details in Help Desk view of Control Hub.

Tabella 2. Set tokenInfoURL
Se Cluster Teams è...	Set tokenInfoURL to...(IdP Proxy URL)
ACHM	https://broadworks-idp-proxy-a.wbx2.com/broadworks-idp-proxy/api/v1/idp/authenticate
Afra	https://broadworks-idp-proxy-k.wbx2.com/broadworks-idp-proxy/api/v1/idp/authenticate
AORE	https://broadworks-idp-proxy-r.wbx2.com/broadworks-idp-proxy/api/v1/idp/authenticate
If you don't know your Teams Cluster, you can obtain the information from the Customer details in the Help Desk view of Control Hub. For testing, you can verify that the tokenInfoURL is valid by replacing the "`idp/authenticate`" portion of the URL with "`ping`".

Configure Identity Providers for Cisco Federation using the following commands:

ADP_CLI/System/CommunicationUtility/DefaultSettings/ExternalAuthentication/CiscoIdentityProvider/Partners> add FederationPartner refreshToken

New Password: <token from service request>

Re-type New Password: <token from service request>

...Done

ADP_CLI/System/CommunicationUtility/DefaultSettings/ExternalAuthentication/CiscoIdentityProvider/Partners> get

Partner Name Refresh Token

==================================

FederationPartner ********

1 entry found.

ADP_CLI/System/CommunicationUtility/DefaultSettings/ExternalAuthentication/CiscoIdentityProvider/Federation>

impostazione flsUrl https://cifls.webex.com/federation
impostare refreshPeriodInMinutes 60
set partnerName FederationPartner

The refresh token is now under the CiscoIdentityProvider/Partners context and the partnerName from the CiscoIdentityProvider/Federation context needs to match the partner added in the CiscoIdentityProvider/Partners context.

If you are running an ADP RI load older than 2022.10, an R23 XSP without patch AP.xsp.23.0.1075.ap383838, or an R22 XSP, then:

You do not need to set a partner under 'System/CommunicationUtility/DefaultSettings/ExternalAuthentication/CiscoIdentityProvider/Federation>'
The refresh token must be set under: System/CommunicationUtility/DefaultSettings/ExternalAuthentication/CiscoIdentityProvider/Federation>

Clear all existing scopes within the following three contexts under ADP_CLI/System/CommunicationUtility/DefaultSettings/ExternalAuthentication/CiscoIdentityProvider/...

Scopes
Admin/RolesAllowed
Admin/ScopesAllowed

For each context, run a get to obtain the existing scopes and then delete them. Ad esempio:

ADP_CLI/System/CommunicationUtility/DefaultSettings/ExternalAuthentication/CiscoIdentityProvider/Scopes> get delete <name_of_scope_1> delete <name_of_scope_2>

ADP_CLI/System/CommunicationUtility/DefaultSettings/ExternalAuthentication/CiscoIdentityProvider/Admin/RolesAllowed> get delete <name_of_scope_1> delete <name_of_scope_2>

ADP_CLI/System/CommunicationUtility/DefaultSettings/ExternalAuthentication/CiscoIdentityProvider/Admin/ScopesAllowed> get delete <name_of_scope_1> delete <name_of_scope_2>

Provision Room OS Devices

On BroadWorks, provision the Room OS device (Webex Board Series, Webex Desk Series, or Webex Room Series).

1	On BroadWorks CommPilot, check the Identity/Device Profile Type configuration to see if the device type exists for this Room OS device. If the device type does not exist on BroadWorks, import the device type into BroadWorks using a DTAF file that you download from cisco.com.
2	After you import the device type, make sure that the following settings exist within the Identity/Device Profile Type configuration: Check the Allow Activation Code Onboarding check box Check the Send Activation Code Request Through Messaging Server check box. Set Authentication Mode to Bearer.
3	Validate that the Device Profile File has the SIP settings that you want to use. In the Identity/Device Profile Type File make sure that Authentication Mode is Bearer.
4	Create a Device Profile with the settings for your new device. In the Identity/Device Profile Add/Modify page, leave the MAC address field empty.
5	Configure the Primary User. On the Users Add page, check or uncheck the isPlace according to whether you intend the device to be personal or for a shared workspace. Checked—Workspace device Unchecked—Personal device Shared workspace devices also require you to assign a primary user. You can assign the primary user that you want.
6	Complete the option that corresponds to the device type and provisioning method that you want to use: Device is for shared workspace—Use the Provision a BroadWorks Workspace API to complete provisioning for the workspace device. Device is personal; you want to provision using public APIs—Use the Provision BroadWorks Subscribers API to complete provisioning for the primary user. Device is personal; you want users to use self-activate—Forward the User Activation Portal URL to the user. The user must validate their email address to complete provisioning. Device is personal; you want to use flowthrough provisioning—Go to step 7.
7	If the device is for personal use, and you want to use flowthrough provisioning, then for the primary user, assign the Integrated IM+P service. On the User > Profile page, add the IM+P service: From the Profile page, click Assign Services. In the list of Available Services, select Integrated IM&P and use the arrow to move the item to the User Services box. Fare clic su OK. Click Profile. Trusted email flow only. Add the user E-mail address. This setting serves as the IM&P email for flowthrough provisioning to Webex for Cisco BroadWorks. This is not required if you are using the untrusted email flow. The Customer Template on Webex must be configured with settings for flowthrough provisioning with trusted emails or untrusted emails. For details, see the Webex for Cisco BroadWorks Solution Guide.

Operazioni successive

Request an activation code for the Room OS device.

Request Activation Code

After your device and user is provisioned on BroadWorks, request that an activation code be sent to the user.

1	In the Identity/Device Profile page, search for and open the device profile for your new device.
2	Click the Device Activation tab.
3	Click Request activation code.

The system generates an activation code and (provided you configured the system properly), the system emails the activation code to the primary user.

Operazioni successive

Provide the device to the user. After the user plugs in the device, they are required to enter the activation code that was sent in the email. This will onboard the device to Webex for Cisco BroadWorks.

MPP Onboarding to Webex

This section describes the onboarding of either new or existing MPP devices to Webex for Cisco BroadWorks. Note that 'existing' refers to an MPP device that exists on BroadWorks, but which does not have Webex capability.

MPP Device Onboarding (New Devices)

During onboarding, the administrator updates BroadWorks with support for MPP, upgrades the device firmware and provisions the device on BroadWorks to complete onboarding.

The following diagram provides an overview of the onboarding process after the activation code that the user enters is validated.

MPP Device Onboarding (Existing Devices)

For existing MPP devices, where the device exists already on BroadWorks, but is not onboarded to Webex, update BroadWorks and the device firmware to support MPP to Webex onboarding. After the updates, the device onboards to Webex automatically.

Ulteriori informazioni

For more information on MPP device onboarding to Webex, refer to the feature description Cisco BroadWorks DMS Enhancements for Webex Enabling MPP Devices.

MPP Device Prerequisites

Minimum MPP Version

MPP firmware 11.3.7 minimum

BroadWorks Patch Requirements

This feature is supported as of version 2021.11 of the Release Independent (RI) ADP server with no patch requirements.

For non-RI servers, you must have installed the following patches (from patch groups ap381367, ap381951, ap382198) in order to use the feature. Install the patches that apply to your release:

Per R22:

AP.as.22.0.1123.ap381367
AP.as.22.0.1123.ap382236
AP.nfm.22.0.1123.ap381367
AP.ns.22.0.1123.ap381367
AP.platform.22.0.1123.ap381367
AP.platform.22.0.1123.ap382198
AP.ps.22.0.1123.ap381367
AP.xsp.22.0.1123.ap381367
AP.xsp.22.0.1123.ap382198

Per R23:

AP.as.23.0.1075.ap381367
AP.as.23.0.1075.ap382236
AP.ns.23.0.1075.ap381367
AP.platform.23.0.1075.ap382198
AP.platform.23.0.1075.ap381367
AP.xsp.23.0.1075.ap381367
AP.xsp.23.0.1075.ap382198
AP.ps.23.0.1075.ap381367

Per R24:

AP.as.24.0.944.ap381367
AP.as.24.0.944.ap381951
AP.as.24.0.944.ap382236

BroadWorks Platform Requirements

This feature is available on:

R22: available on XSP only
R23: available on XSP or ADP (Release Independent)
R24: available on ADP (Release Independent)

BroadWorks Configuration Requirements

To implement this solution, the Flowthrough provisioning must be configured to allow Broadworks to provision devices to Webex.

While configuring the Flowthrough provisioning, it’s not mandatory to use flowthrough provisioning to provision users i.e., you can continue to use your existing provisioning methods (API, Trusted/Untrusted Email, User self, etc.) to provision users. See "Provisioning Requirements" in the Webex for Cisco BroadWorks Solution Guide.
Make sure that the Integrated IM+P service is enabled on BroadWorks and points to the BroadWorks Provisioning Bridge.

The Provisioning Bridge URL was assigned when the Customer Template was applied to the organization. This should have been completed during your initial Webex for Cisco BroadWorks setup. To find the existing URL in Partner Hub, see Configure Application Server with Provisioning Service URL in the Webex for Cisco BroadWorks Solution Guide.
If you have multiple partner organizations, you require a dedicated Device Management Service (DMS) instance per partner.

Certificates and Firewalls

Make sure that you have configured the following:

Certificate Requirements—MPP devices use mTLS authentication using the device certificate. The device MAC address, which the certificate provides, authenticates the device. Download the required certificates for your MPP device from https://www.cisco.com/security/pki/.

Upload your certificates to establish trust on the ADP or firewall. For example, if you’re uploading to the ADP, use this command:

ADP_CLI/Interface/Http/SSLCommonSettings/ClientAuthentication/Trusts/updateTrust> <certificate_filename>
Firewall requirements—If ADP is behind a firewall, your firewall must be configured with a rule to extract the MAC address from the device certificate and place it in an Authentication header that is then forwarded to the ADP. For example, the identity pattern .*([0-9a-fA-F]{12}).* can be used to extract the MAC address, which can then be placed in a header that uses a descriptive name (for example, macaddress).

If ADP is not behind a firewall, the preceding requirement doesn’t exist.

Feature Activation

Activate the following BroadWorks features on the AS:

101377 Enhancements for Webex and MPP device onboarding
25088 Support Handsets for DECT Devices
23775 Remote Reset for MPP Devices
24104 Support Multicell Chaining for DECT devices
20077 Device Management Enhancements
19559 Visual Device Management Enhancements
02283 Device Profile Type Customization Enhancements

For example, run the following command to enable 101377.Change the feature number when activating the other features: AS_CLI/System/ActivatableFeature> activate 101377

Run the following CLI on the Network Server:

NS_CLI/System/DeviceManagement> asLocationLookupEnabled true

Activation Code Requirements

Opzionale. Activation codes are not mandatory for MPP device onboarding. Howver, if you want to use activation codes, see Request Activation Code for MPP for additional requirements that are specific to activation codes with MPP.

MPP Device Onboarding Flow

Complete the following tasks to configure your system to support MPP device onboarding to Webex for Cisco BroadWorks.

If you’re adding Webex capability to an MPP device that exists on BroadWorks already, complete steps 1 and 2 only.

1	Configure Services for MPP (New or existing MPP devices). Configure system support for MPP on Webex for Cisco BroadWorks.
2	Upgrade MPP Device Firmware (Existing MPP devices). For any existing MPP devices for which you want to add Webex capability, upgrade to the latest device firmware.
3	Provision MPP Device (New MPP devices only). If the device doesn’t exist on BroadWorks, provision the device and primary user on BroadWorks.
4	Request Activation Code for MPP (Optional). If you want to use activation codes to onboard MPP devices, request an activation code.

Configure Services for MPP

Update your BroadWorks system settings to support MPP devices (new or existing) on Webex for Cisco BroadWorks. Complete this step once only. You don’t need to repeat this procedure for each MPP device.

Operazioni preliminari

If the ADP is behind a firewall, your firewall must be configured with a rule to extract the MAC address from the device certificate and place it in an Authentication header that is then forwarded to the ADP. For example, the identity pattern .*([0-9a-fA-F]{12}).* can be used to extract the MAC address, which can then be placed in a header that uses a descriptive name (for example, macaddress).

Refer to your firewall documentation for help with the configurations.

Raise a Service Request with your onboarding agent or with Cisco TAC to provision Cisco OAuth for your Cisco Identity Provider Federation account. Use "ADP AuthService Configuration" to title your request.

Cisco fornisce un ID client OAuth, un segreto client e un token di aggiornamento validi per 60 giorni. If the token expires before you use it with your ADP, you can raise another request.

Configure the Cisco Identity Provider parameters by running the following CLI commands.

ADP_CLI/System/CommunicationUtility/DefaultSettings/ExternalAuthentication/CiscoIdentityProvider> set enabled false

set clientId <clientId>—see service request response for ID.
set clientSecret <clientSecret>—see service request response for secret.
set issuerName <URL>—see following table for URL.
set issuerUrl <URL>—see following table for URL.
impostazione di ciResponseBodyMaxSizeInBytes 65536

Tabella 3. Set issuerName and issuerURL
Se Cluster CI è...	Set issuerName and issuerURL to...
USA-A	https://idbroker.webex.com/idb
UE	https://idbroker-eu.webex.com/idb
USA-B	https://idbroker-b-us.webex.com/idb
If you don't know your CI Cluster, you can obtain the information from the Customer details in Help Desk view of Control Hub.

Set the url of the DM Bridge using the below CLI command. The DM Bridge URL is different for each Teams Cluster (which you pulled in Step 2).

ADP_CLI/Applications/BroadworksDms/DeviceActivation/DMBridge> set url = <url_of_DM_Bridge> scope = dm-bridge:device_auth

Tabella 4. DM_Bridge URL
Se Cluster Teams è...	Set DM_Bridge URL to...
ACHM	dm-bridge-a.wbx2.com
AORE	dm-bridge-r.wbx2.com
AFRA	dm-bridge-k.wbx2.com

Enable MAC address extraction and authentication using either the Authentication header or Authentication certificate. For security reasons, we recommend that you use one of the options only:

Authentication header—If ADP is behind a firewall, use the CLI on the ADP to enable MAC address extraction for the Authentication header. This configuration gives the ADP the ability to recognize the MAC address from the Authentication header. Ad esempio:

ADP_CLI/Applications/BroadworksDms/AccessControl/Authentication/Headers> set enable true

ADP_CLI/Applications/BroadworksDms/AccessControl/Authentication/Headers> set identityPattern "macaddress:.*([0-9a-fA-F]{12}).*"

In this example, macaddress is an assigned name with .*([0-9a-fA-F]{12}).* representing the pattern that gets assigned to the header. If you call the header something other than macaddress, adjust your CLI accordingly.
Authentication certificate—If ADP is not behind a firewall, authentication occurs between the device and ADP directly. Use the below CLI commands to enable MAC address extraction on the device certificate for authentication:

ADP_CLI/Applications/BroadworksDms/AccessControl/Authentication/Certificates> set enable true

ADP_CLI/Applications/BroadworksDms/AccessControl/Authentication/Certificates> set identityPattern ".*([0-9a-fA-F]{12}).*"

Upgrade MPP Device Firmware

Operazioni preliminari

Make sure that BroadWorks is updated with services support for MPP.

Upgrade the device firmware to the latest version to ensure that tha the MPP device supports Webex capability.

For more information on firmware upgrades, refer to the Release Notes for your phone model firmware release.

Operazioni successive

Existing MPP devices—After the upgrade, the device onboards to Webex automatically. The user can start using Webex services on the device.
New MPP devices—Provision the new MPP device on BroadWorks.

Provision MPP Device

If the new MPP device does not exist on BroadWorks, provision the device on BroadWorks.

1	On BroadWorks CommPilot, check the Identity/Device Profile Type configuration to see if the device type exists for this MPP device. If the device type doesn’t exist on BroadWorks, import the device type into BroadWorks using a DTAF file that is downloaded from cisco.com.
2	On BroadWorks CommPilot, open the Identity/Device Profile Type and check the Allow Activation Code Onboarding check box.
3	Create an Identity/Device Profile Type File with the SIP settings that you want to use.
4	Create an Identity/Device Profile with settings for your new device. In the MAC address field, enter the device MAC address. If you are using activation codes to onboard MPP devices, leave the MAC address field empty.
5	Configure the Primary User. On the Users Add page, set the isPlace check box according to whether the device is personal or for a shared workspace: Checked—Workspace device Unchecked—Personal device
6	Complete the option that corresponds to the device type and provisioning method that you want to use: Device is for shared workspace—Use the Provision a BroadWorks Workspace API to complete provisioning for the workspace device. Device is personal; you want to provision using public APIs—Use the Provision BroadWorks Subscribers API to complete provisioning for the primary user. Device is personal; you want users to use self-activate—Forward the User Activation Portal URL to the user. The user must validate their email address to complete provisioning. Device is personal; you want to use flowthrough provisioning—Go to step 7.
7	If the device is for personal use, and you want to use flowthrough provisioning, then for the primary user, assign the Integrated IM+P service. On the User > Profile page, add the IM+P service: From the Profile page, click Assign Services. In the list of Available Services, select Integrated IM&P and use the arrow to move the item to the User Services box. Fare clic su OK. Click Profile. Trusted email flow only. Add the user E-mail address. This setting serves as the IM&P email for flowthrough provisioning to Webex for Cisco BroadWorks. This is not required if you are using the untrusted email flow. The Customer Template on Webex must be configured with settings for flowthrough provisioning with trusted emails or untrusted emails. For details, see the Webex for Cisco BroadWorks Solution Guide.

Operazioni successive

Opzionale. If you want to use activation codes to onboard MPP devices, request the activation code on BroadWorks.

Request Activation Code for MPP

(Optional) Webex for Cisco BroadWorks does not require activation codes to onboard new MPP devices. However, if you do decide to use activation codes, complete the Request Activation Code procedure to request an activation code for a new device.

Prerequisites for Using Activation Codes with MPP Devices

If you are using activation code onboarding for MPP devices, make sure that your system meets the following activation code-specific requirements.

Device Activation Service—Complete the following requirements to enable the Device Activation Service:

Deploy the Device Activation Service on BroadWorks. For details, see Cisco BroadWorks Secure Onboarding Using Activation Codes.
Point the Device Activation Service (DAS) to Device Management Services (DMS) on BroadWorks AS using the following CLI command:

AS_CLI/Interface/DAS> set url <url_of_DMS>
Verify that the DAS URL setting for the BroadWorks cluster is set to the Device Management Services (DMS) URL. To view the current DAS URL setting in Partner Hub, go to Settings > BroadWorks Calling > View Clusters and select the appropriate cluster. The URL appears under Interface settings.

Cisco Global Discovery Services (GDS)—GDS is required in order to provision the activation code. Enable GDS on BroadWorks by completing both of the below steps:

Create a service request to provision your GDS account. Cisco provides you with the client ID, client secret, refresh token and GDS domain.

After your GDS account is provisioned, enable GDS on the ADP using the following CLI:

ADP_CLI/Applications/BroadworksDms/DeviceActivation/IdentityProviders/Cisco> get set gdsDomain <gds_domain_from service request> e.g. https://activation.webex.com set clientId <id_from_service_request> clientSecret <secret_from_service_request> refreshToken <token_from_service_request>

In addition to the above activation code-specific prerequisites, your system must meet the general MPP prerequisites in MPP Device Prerequisites.

Request Activation Code

Complete the following steps to request an activation code for a new MPP device.

In the Identity/Device Profile page, search for and open the device profile for your new device.
Click the Device Activation tab.
Click Request activation code.

The system generates the activation code and emails the code to the primary user. The user must enter the code on the device to complete onboarding.

Panoramica sulla funzionalità

Control Hub contiene opzioni di funzionalità che consentono agli amministratori di visualizzare lo stato del dispositivo insieme a una serie di opzioni di manutenzione. Gli amministratori possono:

Visualizza stato dispositivo corrente
Riavvia il dispositivo in remoto
Invio di un report del problema per la risoluzione dei problemi
Elimina il dispositivo

Visualizza stato dispositivo

Utilizzare questa procedura per visualizzare un report di stato del dispositivo da Control Hub. Lo stato include dettagli come lo stato della registrazione, l'indirizzo MAC, l'indirizzo SIP, l'indirizzo IP e il numero di serie.

1	Accedi all'istanza Control Hub per un'organizzazione cliente.
2	Fare clic su Dispositivi.
3	Fare clic sul dispositivo appropriato.

Riavvia dispositivo

Utilizzare questa procedura per riavviare un dispositivo dall'interfaccia Control Hub.

1	Accedi all'istanza Control Hub per un'organizzazione cliente.
2	Fare clic su Dispositivi.
3	Selezionare un dispositivo.
4	Dall'elenco a discesa Azioni , scegliere Riavvia.

Segnala problema

Se si verificano problemi con un dispositivo, utilizzare questa procedura per inviare un report del problema a Cisco TAC per la risoluzione dei problemi.

1	Accedi all'istanza Control Hub per un'organizzazione cliente.
2	Fare clic su Dispositivi.
3	Fare clic sul dispositivo applicabile.
4	Da Azioni, scegliere Segnala problema.
5	Controllate il riepilogo del report.

Elimina dispositivo

Utilizzare questa procedura per eliminare un dispositivo da Control Hub.

1	Accedi all'istanza Control Hub per un'organizzazione cliente.
2	Fare clic su Dispositivi.
3	Selezionare il dispositivo applicabile.
4	Dall’elenco a discesa Azioni , selezionare Elimina.

Modifica proprietario dispositivo

Utilizzare questa procedura per spostare un dispositivo esistente caricato utilizzando i codici di attivazione a un nuovo proprietario del dispositivo.

Questa procedura presuppone che l'opzione Consenti onboarding tramite codice di attivazione sia abilitata per l'identità/profilo dispositivo utilizzato da questo dispositivo.

Elimina la registrazione del dispositivo esistente da Webex:

In Webex Control Hub, aprire l'organizzazione del cliente a cui appartiene l'attuale proprietario del dispositivo.
In Gestione, fai clic su Dispositivi.
Selezionare la casella di controllo adiacente al dispositivo che si desidera spostare.
Fare clic su Elimina

La registrazione del dispositivo viene eliminata da Webex.

Su BroadWorks, disattiva la registrazione del dispositivo sotto l'utente esistente:

In BroadWorks CommPilot, aprire Identity/Device Profile (Identità/profilo dispositivo) utilizzato dal dispositivo.
Fare clic sulla scheda Attivazione dispositivo .
Fare clic su Disattiva dispositivo.

Il dispositivo disattiva e annulla la registrazione da BroadWorks. L'indirizzo MAC viene cancellato dalla configurazione precedente di profilo identità/dispositivo.

Su BroadWorks, attivare il dispositivo utilizzando il codice di attivazione da un altro Identity/Device Profile utilizzato da un altro utente:

Su BroadWorks CommPilot, aprire una configurazione di identità/profilo dispositivo diversa per un utente diverso.
Accertarsi che l'opzione Consenti onboarding tramite codice di attivazione sia selezionata per il tipo di profilo identità/dispositivo utilizzato.
Nella finestra Identità/Profilo dispositivo , fare clic sulla scheda Attivazione dispositivo .
Fare clic su Richiedi un codice di attivazione.

Viene visualizzato il nuovo codice di attivazione. Il nuovo utente deve immettere questo codice per eseguire l'onboarding del dispositivo.

Operazioni successive

Il nuovo proprietario del dispositivo immette il codice di attivazione sul dispositivo.
Il dispositivo esegue nuovamente la registrazione su Webex e BroadWorks utilizzando la nuova configurazione. Il nuovo profilo di identità/dispositivo su BroadWorks si aggiorna automaticamente con l'indirizzo MAC del dispositivo.

Monitoraggio delle prestazioni

Per questa funzione sono disponibili i seguenti contatori delle prestazioni.

Contatore	Descrizione
Modulo: enterprises.broadsoft.broadworks.deviceAttivazione.attiva
bwDASAttivateRichieste	Numero totale di richieste di attivazione ricevute. Ciò include l'attivazione delle richieste BroadWorks e l'attivazione delle richieste Webex.
bwDASAttivateFallimenti	Numero totale di richieste di attivazione non completate.Ciò include l'attivazione delle richieste BroadWorks non riuscite e l'attivazione delle richieste Webex non riuscite.
bwDASActivateBroadWorksRequests	Il numero di richieste di attivare BroadWorks ricevute.
bwDASActivateBroadWorksFailures	Numero di richieste di attivazione BroadWorks non completate correttamente. Gli errori di autorizzazione e autenticazione non sono considerati da questo contatore.
bwDASActivateRichiesteWebex	Il numero di richieste di attivazione Webex ricevute.
bwDASActivateWebexFailures	Numero di richieste di attivazione Webex non completate correttamente.
Modulo: enterprises.broadsoft.broadworks.dms.dmBridge
bwDMBridgeRequests	Il numero di richieste di DMBridge inviate.
bwDMBridgeFallimenti	Numero di richieste DMBridge non completate correttamente.

Guida all'integrazione per Webex per Cisco BroadWorks

Introduzione

Informazioni sulla guida

Cronologia modifiche documento

Integrazione dispositivo per Webex per Cisco BroadWorks

Device Onboarding Overview

Room OS Onboarding

Device Onboarding with Activation Codes

Onboarding Process for Room OS

Device Authentication (via OAuth Bearer Tokens)

Room OS Prerequisites

Minimum Room OS Version

BroadWorks Patch Requirements

BroadWorks Platform Requirements

BroadWorks Configuration Requirements

Prerequisites for Activation Code Onboarding with Room OS

Room OS Onboarding Flow

Configure Services for Room OS

Provision Room OS Devices

Request Activation Code

MPP Onboarding to Webex

MPP Device Onboarding (New Devices)

MPP Device Onboarding (Existing Devices)

Ulteriori informazioni

MPP Device Prerequisites

Minimum MPP Version

BroadWorks Patch Requirements

BroadWorks Platform Requirements

BroadWorks Configuration Requirements

Certificates and Firewalls

Feature Activation

Activation Code Requirements

MPP Device Onboarding Flow

Configure Services for MPP

Upgrade MPP Device Firmware

Provision MPP Device

Request Activation Code for MPP

Prerequisites for Using Activation Codes with MPP Devices

Request Activation Code

Funzionalità dispositivo

Panoramica sulla funzionalità

Visualizza stato dispositivo

Riavvia dispositivo

Segnala problema

Elimina dispositivo

Modifica proprietario dispositivo

Monitoraggio delle prestazioni

Funzioni utente finale per dispositivi integrati Webex

Cronologia chiamate Unified

Telefoni MPP consapevoli di Webex

Dispositivi RoomOS integrati Webex per BroadWorks

Miglioramenti alla ricerca nella rubrica per i dispositivi RoomOS integrati Webex per BroadWorks

Small Business

Aziendale

Dispositivi

Soluzioni per

Risorse

Società